KNOW HOW, KNOW WHY, GET TRAINED
(941) 730-6576
My Aunts Are Lossing Control Md0186 Aeace New ((better)) Site
© 2025 American Crane & Safety,LLC
At the heart of any effective safety program is a constant effort to ensure that employees have the proper knowledge and skill for all aspects of their job. Rigging and lifting clearly is an operation that has been shown to require knowledge and skills. Accidents also can harm your companies’ brand and reputation. Having a well-trained lift team can help mitigate, and possibly eliminate some of the hazards associated with using cranes. A safe lift depends on a number of people filling roles including operators, riggers, journeyman riggers, signal persons, crane owners, crane users, lift directors, supervisors, and the communication between those people.
A qualified person as to whether it constitutes a hazard. And if so, what additional steps need to be taken to address the hazard and how it can be eliminated. And, shall have a thorough education, training, experience, skill and physical ability, as necessary, be competent and capable to perform the functions as determined by the employer or employer’s representative. Sling working load limits (WLL) are based on items being in acceptable condition before being used per ASME B30.9, OSHA 1910.184 and the manufacturer’s recommendations and limitations for use.
The MAXIMUM load that shall be applied in direct tension to undamaged straight length of a sling or hoisting equipment.
Are of the utmost importance and anyone purchasing and using items must understand all warnings and other information on the product being used. Products are sold with express understanding that the purchaser is thoroughly familiar with the correct application and safe use for which they were intended.
Any product will break if abused, misused or overused. Any well-designed and well-built product can become a hazard in the hands of careless users. It is impossible to list all of the possible dangers and misapplications associated with the use of products.
A formal diagnosis is critical to understanding if the behavior is due to neurodegeneration (like Alzheimer's) or other reversible conditions. Primary Care Physician:
Then came the first mention of .
Whether it's about emotional outbursts, financial mismanagement, declining health, or interpersonal chaos, watching aunts—especially those who were once pillars of strength—begin to lose control can be deeply unsettling. Add to that a bizarre, seemingly technical suffix like , and you might be dealing with a mis-typed internal code, an online reference, or a corrupted search term.
A week later, I was helping Aunt Mae clean out her basement office. Buried under tax returns from 2017 was a folder labeled .
. If an aunt is "losing the plot," it often says more about her own stress levels than it does about you. 4. Prioritize Self-Care
could be:
: Try to have an open and non-judgmental conversation with your aunts. Express your concern in a caring and empathetic way. Sometimes, just knowing that someone is there to listen can be a huge relief.
It's clear that you're concerned about your aunts' well-being, and your support can make a significant difference. Encouraging them to seek professional help, offering to assist with daily tasks, and being a listening ear can be valuable steps. If you're unsure about how to proceed, consider reaching out to a professional for guidance tailored to their specific needs.
With the following information on the tag
This happens when wire fractures between the strands coming from the core it is usually caused by a shock load
Just 1 broken wire requires the sling to be removed from service!
| WORKING LOAD LIMIT (lbs.) | ||
| End Fitting Types | ||
| Size (Inches) | Hook & Eye Hook & Hook | Eye & Eye Eye & Jaw Jaw & Jaw |
| 1/4 | 400 | 500 |
| 5/16 | 700 | 800 |
| 3/8 | 1,000 | 1,200 |
| 1/2 | 1,500 | 2,200 |
| 5/8 | 2,250 | 3,500 |
| 3/4 | 3,000 | 5,200 |
| 7/8 | 4,000 | 7,200 |
| 1 | 5,000 | 10,000 |
| 1-1/4 | 6,500 | 15,200 |
| 1-1/2 | 7,500 | 21,400 |
EYEBOLTS MAXIMUM TEMPERATURE 275°
THIS IS A SHOULDERED EYEBOLT IT CAN BE PULLED IN THE PLANE OF THE EYE AT NO GREATER THAN 45° AND HAS ONLY 25% OF ITS CAPACITY
| Size (in.) | WORKING LOAD LIMIT (lbs.) | |||
| 0° True Vertical | 75° 55% of FULL WLL | 65° 35% of FULL WLL | 45° 25% of FULL WLL | |
| 1/4x20 | 500 | 275 | 175 | 125 |
| 5/16x18 | 900 | 495 | 315 | 225 |
| 3/8x16 | 1,300 | 715 | 455 | 325 |
| 7/16x14 | 1,800 | 990 | 630 | 450 |
| 1/2x13 | 2,400 | 1,320 | 840 | 600 |
| 5/8x11 | 4,000 | 2,200 | 1,400 | 1,000 |
| 3/4x10 | 5,000 | 2,750 | 1,750 | 1,250 |
| 7/8x9 | 7,000 | 3,850 | 2,450 | 1,750 |
| 1x8 | 9,000 | 4,950 | 3,150 | 2,250 |
| 1-1/8x7 | 12,000 | 6,600 | 4,200 | 3,000 |
| 1-1/4x7 | 15,000 | 8,250 | 5,250 | 3,750 |
| 1-1/2x6 | 21,000 | 11,550 | 7,350 | 5,250 |
MUST BE ABLE TO ROTATE 360° AND PIVOT 180°
| Size (in.) | Rated Load (lbs.) | Torque Load (lbs-ft) | Dimensions (in.) | ||
| A | D | M | |||
| 1/4-20 | 500 | 5 | 0.65 | 0.44 | 1.57 |
| 5/16-18 | 800 | 7 | 0.65 | 0.44 | 1.51 |
| 3/8-16 | 1,000 | 12 | 0.65 | 0.44 | 1.45 |
| 1/2-13 | 2,500 | 28 | 1.00 | 0.75 | 2.56 |
| 5/8-11 | 4,000 | 60 | 1.00 | 0.75 | 2.44 |
| 3/4-10 | 5,000 | 100 | 1.00 | 0.75 | 2.31 |
| 3/4-10 | 7,000 | 100 | 1.00 | 1.00 | 2.31 |
| 7/8-9 | 8,000 | 160 | 1.40 | 1.00 | 3.07 |
| 1-8 | 10,000 | 230 | 1.40 | 1.00 | 2.95 |
| 1-1/4-7 | 15,000 | 470 | 1.40 | 1.00 | 3.74 |
| 1-3/8-6 | 20,000 | 670 | 2.00 | 1.25 | 3.62 |
| 1-1/2-6 | 24,000 | 800 | 2.00 | 1.25 | 3.49 |
| 2-4-1/2 | 30,000 | 800 | 2.00 | 1.25 | 3.49 |
| 2-8 | 30,000 | 800 | 2.00 | 1.25 | 3.49 |
| Rope Diameter (in.) | No. of Clips | Turnback (in.) | Torque (ft-lbs)(unlubed bolts) |
| 1/8 | 2 | 3-1/4 | 4-1/2 |
| 3/16 | 2 | 3-3/4 | 7-1/2 |
| 1/4 | 2 | 4-3/4 | 15 |
| 5/16 | 2 | 5-1/4 | 30 |
| 3/8 | 2 | 6-1/2 | 45 |
| 7/16 | 2 | 7 | 65 |
| 1/2 | 3 | 11-1/2 | 65 |
| 9/16 | 3 | 12 | 95 |
| 5/8 | 3 | 12 | 95 |
| 3/4 | 4 | 618 | 130 |
| 7/8 | 4 | 20 | 225 |
| 1 | 5 | 26 | 225 |
BOLTS: All bolts should have sufficient plain length to pass through half the component. Check integrity & tightness.
NUTS: All nuts when tightened should have 2 threads protruding. All nits should be locked with Loctite grade 270, nylon insert, or self-cleaving. Check for integrity & tightness.
CHAIN: All chain should be tested in accordance with ASME B30.9 recommendations.
There have been recent changes to magnet inspections and testing that everyone needs to be aware of. The ASME 820.20-2018 standard states Lifting Magnets should have an annual Breakaway Test to verify the magnet meets its design factor.
| Angle of Choke | Rated Capacity |
| Over 120° | 100% |
| 90° - 120° | 87% |
| 60° - 89° | 74% |
| 39° - 59° | 62% |
| 0 - 29° | 49% |
Maximum angle for 2 slings in a choke
Maximum angle for 2 slings in a double wrapped choke
GENERAL NOTE: When D is 25 times the component rope diameter (d), the D/d ratio is expressed as 25/1.
| D/d Ratio | Capacity |
| 25/1 | 100% |
| 20/1 | 92% |
| 10/1 | 86% |
| 4/1 | 75% |
| 2/1 | 65% |
| 1/1 | 50% |
| D/d Ratio | Capacity |
| 6/1 | 100% |
| 5/1 | 90% |
| 4/1 | 80% |
| 3/1 | 70% |
| 2/1 | 60% |
| 1/1 | Not Recommended |
This tension is also referred to as the
LOAD ANGLE FACTOR (L.A.F.)
IT IS CALCULATED BY DIVIDING THE S OR SLING LENGTH BY THE H OR HEIGHT TO THE SAME POINT ON THE SLING
Since 30° is the lowest horizontal sling angle that you can use when rigging, the horizontal angles on this table below start at 30°
| Horizontal Angle | Load Angle Factor |
| 30° | 2 |
| 35° | 1.742 |
| 40° | 1.555 |
| 45° | 1.414 |
| 50° | 1.305 |
| 55° | 1.221 |
| 60° | 1.155 |
| 65° | 1.104 |
| 70° | 1.064 |
| 75° | 1.035 |
| 80° | 1.015 |
| 85° | 1.004 |
| 90° | 1 |
Multiple slings within the body of the shackle shall not exceed 120° included angle
The maximum included angle with two or more slings is listed below for hooks, master links and shackles.
| Connections | ||
 |  |  |
| Hooks 90° | Master links 120° | Shackles 120° |
Hooks having any of the following conditions shall be removed from service until repaired or replaced:
| Angles in Degrees | Working Load Limit Reduction |
| 0° to 10° | 0% |
| 11° to 20° | 15% |
| 21° to 30° | 25% |
| 31° to 45° | 30% |
| 46° to 55° | 40% |
| 56° to 70° | 45% |
| 71° to 90° | 50% |
Shackles can be connected together, or point loaded
Always attach the slings to the bow of the shackle, pin in the hook
The bow of the shackle should always be in the running part of the sling pin in the eye of the sling
When using a single sling, load should stay centered or capacity reductions are necessary
When using in a wire rope sling always use the next size larger
The shackle must be the next size larger than the wire rope sling diameter to achieve full capacity of the sling
ASME B30.26 has the following statement regarding screw pin shackles:
The screw pin threads shall be fully engaged and tight and the shoulder should be in contact with the shackle body.
Thus, contrary to popular belief, you should never back off the screw pin before use. The shackle pin should be a minimum of hand tight before the lift begins.
Shackles are designed and rated for in-line applied tension. You can attach multiple slings in the body of the shackle without reducing the capacity, provided that the shackle is symmetrically loaded and the included angle does not exceed 120°.
| Size (in.) | WLL (tons) | WLL (lbs.) | Pin Diameter (in.) | W dim. (in.) |
| 3/16 | 1/3 | 667 | 0.25 | 0.38 |
| 1/4 | 1/2 | 1,000 | 0.31 | 0.47 |
| 5/16 | 3/4 | 1,500 | 0.38 | 0.53 |
| 3/8 | 1 | 2,000 | 0.44 | 0.66 |
| 7/16 | 1-1/2 | 3,000 | 0.50 | 0.72 |
| 1/2 | 2 | 4,000 | 0.63 | 0.84 |
| 5/8 | 3-1/4 | 6,500 | 0.75 | 1.06 |
| 3/4 | 4-3/4 | 9,500 | 0.88 | 1.28 |
| 7/8 | 6-1/2 | 13,000 | 1.00 | 1.44 |
| 1 | 8-1/2 | 17,000 | 1.13 | 1.72 |
| 1-1/8 | 9-1/2 | 19,000 | 1.25 | 1.84 |
| 1-1/4 | 12 | 24,000 | 1.38 | 2.03 |
| 1-3/8 | 13-1/2 | 27,000 | 1.50 | 2.25 |
| 1-1/2 | 17 | 34,000 | 1.63 | 2.41 |
| 1-5/8 | 20 | 40,000 | 1.75 | 2.66 |
| 1-3/4 | 25 | 50,000 | 2.00 | 2.94 |
| 2 | 35 | 70,000 | 2.25 | 3.28 |
| 2-1/2 | 55 | 110,000 | 2.75 | 4.13 |
| 3 | 85 | 170,000 | 3.25 | 5.00 |
| 3-1/2 | 120 | 240,000 | 3.75 | 5.50 |
Shackles can be used to connect slings | WARNING NEVER TIE SLINGS TOGETHER OR DIRECTLY TO LIFTING BOLTS/LUGS |
 |  |
It's the user's responsibility to protect the sling from the load Sharp edges and corners can cut slings causing sling failure and damage Padded material can help protect the sling Changing the corner profile can help | |
ASME B-30.9 Standard for slings states that “…Sling users SHALL be trained in the selection, inspection, cautions to personnel, effects of environment, and rigging practices…”
NOTE: Round sling strength is affected by the size of the connection hardware. For special applications wherein a Retained design factor of 5 is required to be maintained, contact the sling manufacturer, as a capacity reduction of 20% may be appropriate in order to satisfy this criteria.
 |  |
| Vertical Rated Capacity | Vertical | Basket |
| Minimum Shackle Size Required | ||
| 2,600 | 1/2" | 3/4" |
| 5,300 | 3/4" | 1" |
| 8,400 | 7/8" | 1-3/8" |
| 10,600 | 1" | 1-1/2" |
| 13,200 | 1-1/4" | 1-5/8" |
| 16,800 | 1-3/8" | 1-3/4" |
| 21,200 | 1-1/2" | 2" |
| 25,000 | 1-5/8" | 2-1/2" |
| 31,000 | 1-3/4" | 2-1/2" |
| 40,000 | 2" | 2-3/4" |
| 53,000 | 2-1/2" | 3" |
| 66,000 | 2-1/2" | 3-1/2" |
| 90,000 | 3" | 4" |
NOTE: Round sling strength is affected by the size of the connection hardware. For special applications wherein a Retained design factor of 5 is required to be maintained, contact the sling manufacturer, as a capacity reduction of 20% may be appropriate in order to satisfy this criteria.
A formal diagnosis is critical to understanding if the behavior is due to neurodegeneration (like Alzheimer's) or other reversible conditions. Primary Care Physician:
Then came the first mention of .
Whether it's about emotional outbursts, financial mismanagement, declining health, or interpersonal chaos, watching aunts—especially those who were once pillars of strength—begin to lose control can be deeply unsettling. Add to that a bizarre, seemingly technical suffix like , and you might be dealing with a mis-typed internal code, an online reference, or a corrupted search term. my aunts are lossing control md0186 aeace new
A week later, I was helping Aunt Mae clean out her basement office. Buried under tax returns from 2017 was a folder labeled .
. If an aunt is "losing the plot," it often says more about her own stress levels than it does about you. 4. Prioritize Self-Care A formal diagnosis is critical to understanding if
could be:
: Try to have an open and non-judgmental conversation with your aunts. Express your concern in a caring and empathetic way. Sometimes, just knowing that someone is there to listen can be a huge relief. Add to that a bizarre, seemingly technical suffix
It's clear that you're concerned about your aunts' well-being, and your support can make a significant difference. Encouraging them to seek professional help, offering to assist with daily tasks, and being a listening ear can be valuable steps. If you're unsure about how to proceed, consider reaching out to a professional for guidance tailored to their specific needs.
OSHA SAY’S IT’S USERS RESPONSIBILITY TO STAY OUT OF THE WAY OF THE LOADTHE CLOSEST YOU SHOULD GET IS ARMS REACH |  |
It is important that the CG is directly under the crane hook.
STABLE
The hook lift point is directly above the CG.
Lift points are ABOVE the CG.
Smooth, steady application of lifting force
THIS IS WHAT CAN HAPPEN IF YOU WRAP THE CHAIN AROUND THE LOAD
THESE HOISTS ARE ONLY MADE FOR A STRAIGHT PULL
USE SLINGS AROUND THE OBJECT BEING LIFTED
Hooks shall be equipped with latches unless use of the latch creates a hazardous condition
